Xantrex-technology MS2000 Bedienungsanleitung Seite 47
- Seite / 126
- Inhaltsverzeichnis
- FEHLERBEHEBUNG
- LESEZEICHEN
Bewertet. / 5. Basierend auf Kundenbewertungen
Operation
975-0125-02-01 2–17
Charger Operation with Battery Temperature Sensor
Since battery temperature is a key factor in optimal charging, the house battery
charger voltage will be adjusted (automatically and continuously) according to the
actual battery temperature to ensure that the house battery is fully charged, but not
overcharged. For this reason, Xantrex has included a battery temperature sensor
(see Figure 2-11) with your MS2000 Sine Wave Inverter/Charger that allows the
main charger to provide this temperature-compensated charge formula. The Echo
Charger output bank is not temperature compensated.
The battery temperature sensor continuously measures the temperature of the
house battery and adjusts the main charger output for a more accurate,
temperature-compensated charge.
When batteries are cold, their chemical reaction is sluggish, meaning they don’t
absorb charge as easily. Thus a charge level optimized for room temperature will
not charge the batteries sufficiently if they are cold. The main charger must
compensate by increasing its voltage to achieve the compensated equivalent of a
room temperature charge.
If the batteries are hot, the chemical reaction is hyperactive and they absorb
energy too easily; thus a standard room-temperature charge would tend to
overcharge a hot battery. Therefore, the main charger compensates by reducing its
voltage.
The battery temperature sensor automatically, and continuously, makes
adjustments to the main charger’s voltage setpoints to properly charge your
batteries. The actual charge compensation formula can be found on page A–3.
If a battery temperature sensor is not present, the MS2000 uses the cold, warm,
and hot settings. Charging may not be effective at extreme temperatures. See
“Main Charger Specifications” on page A–3.
Important:
It is normal to see a voltage that is different than the specified
setpoint when charging if the battery case temperature is above or below 77 °F
(25 °C)
Figure 2-11
Battery Temperature Sensor
- Operation Guide 1
- About This Guide 5
- Conventions Used 6
- Symbols Used 6
- Related Information 7
- Contact Information 7
- Important Safety Instructions 9
- Explosive Gas Precautions 11
- FCC Information to the User 12
- Contents 13
- Configuration 14
- Troubleshooting 15
- 975-0125-02-01 xv 17
- Introduction 19
- Premium Power and Ease of Use 20
- How MS2000 Works 21
- 1–4 975-0125-02-01 22
- Xanbus System 23
- Xanbus Enabled 23
- MS2000 Features 25
- Figure 1-3 26
- Table 1-2 26
- Side Panel Features 27
- CAUTION: Equipment Damage 27
- Figure 1-5 28
- DC Grounding Completed 28
- DC Terminal Covers 29
- Battery Temperature Sensor 29
- Operation 31
- Important: 32
- On Start Up 34
- Power On Reset 34
- System Start-up Check 35
- System Modes 36
- Operate Mode 37
- Power Save Mode 37
- Safe Mode 38
- CAUTION: Unexpected behavior 38
- 975-0125-02-01 2–9 39
- Hibernate mode 40
- 975-0125-02-01 2–11 41
- Operating in Invert Mode 42
- Power Output 43
- Operating in Charger Mode 44
- Echo Charger Operation 45
- 2–16 975-0125-02-01 46
- WARNING: Explosive gases 48
- Equalizing Batteries 49
- Power Share 52
- Faults and Warnings 54
- System Control 56
- System Menu Map 57
- Viewing the System Screen 58
- 975-0125-02-01 3–5 59
- MS2000 Configuration Menus 60
- 975-0125-02-01 3–7 61
- MS2000 Device Menu 62
- AC Input 63
- Echo Chg Out 63
- MS2000 Menu (Basic) 64
- Equalize 66
- 975-0125-02-01 3–13 67
- 3–14 975-0125-02-01 68
- Batt Type 69
- Batt Size 69
- Clear Faults 70
- MS2000 Menu (Advanced) 71
- Max Chg Rate 72
- Echo Chg 72
- Load Sense 73
- View Device Info 73
- Basic Menu 73
- 975-0125-02-01 3–21 75
- Sub-Menus 76
- Sense Interval 77
- # Chg Stages 77
- Eqz Volts 78
- Force Charge 78
- Lo AC Volt 79
- Lo AC Freq 79
- Hi AC Volt 80
- Hi AC Freq 80
- View Fault Log 81
- View Warning Log 81
- View Event Log 81
- Restore Defaults 82
- Warning Types 85
- Troubleshooting Reference 86
- 975-0125-02-01 4–5 87
- Warning Messages 88
- Table 4-3 89
- Fault Messages 91
- Table 4-4 92
- Inverter Applications 97
- Searching 98
- Specifications 99
- Inverter Specifications 100
- Main Charger Specifications 101
- Echo Charger Specifications 102
- Environmental Specifications 103
- Regulatory Approvals 103
- Fan Operation 103
- Charger Mode 104
- Reference for the Main 105
- Battery Charging 105
- Charge Algorithm Stages 106
- Bulk Charge 107
- Absorption Charge 107
- Float Charge 107
- Two-Stage Charging 108
- Charge Algorithm Graph 109
- Charge Algorithm Definitions 109
- AC Reconnect Summary 110
- Terminology 111
- Glossary 112
- Abbreviations 115
- Warranty 117
- Disclaimer 118
- Return Procedure 119
- Out of Warranty Service 119
- Information About Your System 120
- Xantrex Technology Inc 126
Verwandte Produkte und Handbücher für Generatoren Xantrex-technology MS2000
(74 Seiten)© 2020, manymanuals.de. Alle Rechte vorbehalten. | 0.063 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Kommentare zu diesen Handbüchern